您现在的位置： 电子商务模式 >> 电子商务技术 >> 教程 >> [EB技术]正文  显示方式： 

Cisco交换机综合配置实例(一)
http://tech.caneb.com/ 时间：2006-6-2 点击数：   电子商务模式[技术]频道　

今日不可不关注的电子商务技术资讯：

本实例综合性很强,基本上包含了Cisco交换机的所有交换技术

1.　网络拓扑和相应设计

目录:

网络配置实例

网络拓扑和相应设计

Catalyst 5509 配置

Catalyst 4003　配置

RSM　配置

Catalyst 5505　配置

网络拓扑和相关设计

网络拓扑图

　

　

　

　

　

　



2.　Catalyst 5509 的配置

下面列出 Catalyst 5509 的基本配置

Enter password:

Console> enable

Enter password:

Console> (enable) set system name 5509-ER-F1

System name set.

5509-ER-F1> (enable) set system location 1st Floor Equipment Room

System location set.

5509-ER-F1> (enable) set system contact sysadmin@bigcorp.com

System contact set.

5509-ER-F1> (enable) set time 04/30/1999 9:30:00

Fri Apr 30 1999, 09:30:00

5509-ER-F1> (enable) set password

Enter old password:

Enter new password:

Retype new password:

Password changed.

5509-ER-F1> (enable) set enablepass

Enter old password:

Enter new password:

Retype new password:

Password changed.

5509-ER-F1> (enable) set banner motd %

5509-ER-F1 (Catalyst 5509)

Access Restricted

%

MOTD banner set

5509-ER-F1> (enable) set interface sc0 10.10.1.10/24

Interface sc0 IP address set.

5509-ER-F1> (enable) set ip route default 10.10.1.1

Route added.

5509-ER-F1> (enable) set ip dns server 10.10.10.100

10.10.10.100 added to DNS server table as primary server.

5509-ER-F1> (enable) set ip dns domain bigcorp.com

Default DNS domain name set to bigcorp.com

5509-ER-F1> (enable) set ip dns enable

DNS is enabled

5509-ER-F1> (enable) set vtp domain BigCorp mode server

VTP domain BigCorp modified

5509-ER-F1> (enable) set vlan 10 name Corporate

Vlan 10 configuration successful

5509-ER-F1> (enable) set vlan 20 name DevEng

Vlan 20 configuration successful

5509-ER-F1> (enable) set vlan 30 name Mfg

Vlan 30 configuration successful

5509-ER-F1> (enable) set vlan 40 name QA

Vlan 40 configuration successful

5509-ER-F1> (enable) set vlan 50 name Finance&Admin

Vlan 50 configuration successful

5509-ER-F1> (enable) set vlan 60 name Sales&Mktg

Vlan 60 configuration successful

5509-ER-F1> (enable) set module name 1 Supervisor III

Module name set.

5509-ER-F1> (enable) set port flowcontrol 1/1-2 send off

Ports 1/1-2 flow control send administration status set to off

(ports will not send flowcontrol to far end)

5509-ER-F1> (enable) set port flowcontrol 1/1-2 receive off

Ports 1/1-2 flow control receive administration status set to off

(ports will not allow far end to send flowcontrol)

5509-ER-F1> (enable) set port negotiation 1/1-2 enable

Ports 1/1-2 negotiation enabled

5509-ER-F1> (enable) set port name 1/1-2 GEC 802.1Q Trunk

Ports 1/1-2 name set.

5509-ER-F1> (enable) set port channel 1/1-2 desirable

Port(s) 1/1-2 channel mode set to desirable.

5509-ER-F1> (enable) set trunk 1/1 desirable dot1q

Port(s) 1/1 trunk mode set to desirable.

Port(s) 1/1 trunk type set to dot1q.

5509-ER-F1> (enable) set module name 3 RSM (RSM-ER-F1)

Module name set.

5509-ER-F1> (enable) set module name 5 Fast Ether Uplinks

Module name set.

5509-ER-F1> (enable) set port name 5/1-4 FEC ISL Trunk

Ports 5/1-4 name set.

5509-ER-F1> (enable) set port speed 5/1-4 100

Ports 5/1-4 transmission speed set to 100Mbps.

5509-ER-F1> (enable) set port duplex 5/1-4 full

Ports 5/1-4 set to full-duplex.

5509-ER-F1> (enable) set port flowcontrol 5/1-4 send off

Ports 5/1-4 flow control send administration status set to off

(ports will not send flowcontrol to far end)

5509-ER-F1> (enable) set port flowcontrol 5/1-4 receive off

Ports 5/1-4 flow control receive administration status set to off

(ports will not allow far end to send flowcontrol)

5509-ER-F1> (enable) set port negotiation 5/1-4 enable

Ports 5/1-4 negotiation enabled

5509-ER-F1> (enable) set port channel 5/1-4 desirable

Port(s) 5/1-4 channel mode set to desirable.

5509-ER-F1> (enable) set trunk 5/1 desirable isl

Port(s) 5/1 trunk mode set to desirable.

Port(s) 5/1 trunk type set to isl.

5509-ER-F1> (enable) set module name 6 DevEng 100Mb Hosts

Module name set.

5509-ER-F1> (enable) set port name 6/1 DE Sparc Ultra

Port 6/1 name set.

5509-ER-F1> (enable) set port name 6/2-7 DE Sparc20

Ports 6/2-7 name set.

5509-ER-F1> (enable) set port name 6/8-12 DE NT Workstation

Ports 6/8-12 name set.

5509-ER-F1> (enable) set port speed 6/1-12 100

Ports 6/1-12 transmission speed set to 100Mbps.

5509-ER-F1> (enable) set port duplex 6/1-12 full

Ports 6/1-12 set to full-duplex.

5509-ER-F1> (enable) set port flowcontrol 6/1-12 send desired

Ports 6/1-12 flow control send administration status set to desired

(ports will send flowcontrol to far end if far end supports it)

5509-ER-F1> (enable) set port flowcontrol 6/1-12 receive desired

Ports 6/1-12 flow control receive administration status set to desired

(ports will allow far end to send flowcontrol if far end supports it)

5509-ER-F1> (enable) set port channel 6/1-12 off

Port(s) 6/1-12 channel mode set to off.

5509-ER-F1> (enable) set trunk 6/1-12 off

Port(s) 6/1-12 trunk mode set to off.

5509-ER-F1> (enable) set spantree portfast 6/1-12 enable

Warning: Spantree port fast start should only be enabled on ports connected

to a single host. Connecting hubs, concentrators, switches, bridges, etc. to

a fast start port can cause temporary spanning tree loops. Use with caution.

Spantree ports 6/1-12 fast start enabled.

5509-ER-F1> (enable) set vlan 20 6/1-12

VLAN 20 modified.

VLAN 1 modified.

VLAN　Mod/Ports

---- -----------------------

201/1-2

　5/1-4

　6/1-12

　

5509-ER-F1> (enable) set module name 7 Corp/Mfg 10Mb Hosts

Module name set.

5509-ER-F1> (enable) set port name 7/1-12 Corp Win98 PC

Ports 7/1-12 name set.

5509-ER-F1> (enable) set port name 7/13-48 Mfg Win98 PC

Ports 7/13-48 name set.

5509-ER-F1> (enable) set port duplex 7/1-48 full

Ports 7/1-48 set to full-duplex.

5509-ER-F1> (enable) set spantree portfast 7/1-48 enable

Warning: Spantree port fast start should only be enabled on ports connected

to a single host. Connecting hubs, concentrators, switches, bridges, etc. to

a fast start port can cause temporary spanning tree loops. Use with caution.

Spantree ports 7/1-48 fast start enabled.

5509-ER-F1> (enable) set vlan 10 7/1-12

VLAN 10 modified.

VLAN 1 modified.

VLAN　Mod/Ports

---- -----------------------

101/1-2

　5/1-4

　7/1-12

　

5509-ER-F1> (enable) set vlan 30 7/13-48

VLAN 30 modified.

VLAN 1 modified.

VLAN　Mod/Ports

---- -----------------------

301/1-2

　5/1-4

　7/13-48

　

5509-ER-F1> (enable) set module name 8 DevEng 10Mb Hosts

Module name set.

5509-ER-F1> (enable) set port name 8/1-48 DevEng WinNT PC

Ports 8/1-48 name set.

5509-ER-F1> (enable) set port duplex 8/1-48 full

Ports 8/1-48 set to full-duplex.

5509-ER-F1> (enable) set spantree portfast 8/1-48 enable

Warning: Spantree port fast start should only be enabled on ports connected

to a single host. Connecting hubs, concentrators, switches, bridges, etc. to

a fast start port can cause temporary spanning tree loops. Use with caution.

Spantree ports 8/1-48 fast start enabled.

5509-ER-F1> (enable) set vlan 20 8/1-48

VLAN 20 modified.

VLAN 1 modified.

VLAN　Mod/Ports

---- -----------------------

201/1-2

　5/1-4

　6/1-12

　8/1-48

　

5509-ER-F1> (enable) set module name 9 DevEng 10Mb Hosts

Module name set.

5509-ER-F1> (enable) set port name 9/1-48 DevEng WinNT PC

Ports 9/1-48 name set.

5509-ER-F1> (enable) set port duplex 9/1-48 full

Ports 9/1-48 set to full-duplex.

5509-ER-F1> (enable) set spantree portfast 9/1-48 enable

Warning: Spantree port fast start should only be enabled on ports connected

to a single host. Connecting hubs, concentrators, switches, bridges, etc. to

a fast start port can cause temporary spanning tree loops. Use with caution.

Spantree ports 9/1-48 fast start enabled.

5509-ER-F1> (enable) set vlan 20 9/1-48

VLAN 20 modified.

VLAN 1 modified.

VLAN　Mod/Ports

---- -----------------------

201/1-2

　5/1-4

　6/1-12

　8/1-48

　9/1-48

　

5509-ER-F1> (enable)


关键词：交换机
阅读本站更多关于：“Cisco交换机综合配置实例(一)”的文章>>>>
作者：佚名 文章来源：网络
[EB技术]录入：北极星    责任编辑：北极星 

  • 上一篇[EB技术]：

  • 下一篇[EB技术]：
    •   窄告信息
    电子商务辩论台：
    网友评论：（只显示最新10条。评论内容只代表网友观点，与本站立场无关！）
    电子商务模式网站（www.CanEb.com）版权与免责声明：
    ① 本网转载其他媒体、网站文章是为传播更多的信息，此类文章不代表本网观点，也不对其真实性负责，本网不承担此类文章侵权行为的连带责任。
    ② 在本网论坛（BBS）、博客（Blog）、网络硬盘（WebDisk）上发表言论或上传、收藏文件者，责任自负。
    ③ 如您因版权等问题需要与本网联络，请在30日内联系 caneb_com@yahoo.com.cn 。
    ④ 凡本网原创文章（包括论坛、博客等），欢迎转载，但务必注明来自本网，且需注明引用网址。
    焦点图片
    今日博客
    电子商务模式网站意见反馈留言板